#Loose transmission filter symptoms how to
#Loose transmission filter symptoms code
#Loose transmission filter symptoms Bluetooth
#Loose transmission filter symptoms professional

With the tool connected, turn on the ignition. The OBDII connector is usually located under the dashboard. To begin troubleshooting, you must first connect the diagnostic tool to your Silverado 1500.

#Loose transmission filter symptoms Bluetooth

You can use a standalone diagnostic device (shown above) or get an OBD2 adapter that connects with a smartphone app via Bluetooth or WiFi. OBD2 scanners are now available in various designs. Since Chevy Silverado 1500 is equipped with on-board diagnostics (OBD), a fault diagnosis can provide initial indications of where the malfunction is located. Also, do not use anything other than the MAF cleaner to clean the sensor, otherwise the sensor may get damaged. Note: Do not use a cloth or cotton swabs to clean the sensor. Put everything back together and start the engine.Spray at least 10 spurts of MAF cleaner onto the sensor and then let it air dry for an hour or until completely dry.Find the location of the MAF sensor in your Silverado 1500, it will be somewhere between the air filter box and the throttle body.However, caution is advised here, as the sensor parts are very sensitive to touch. Cleaning dirty MAF sensor in Chevy Silverado 1500Ĭleaning the mass air flow sensor can help the sensor measure the correct values again, but only if the erroneous readings are caused by dirt accumulation.

#Loose transmission filter symptoms professional

However, this should be best left to trained professional mechanics, as it requires reading and interpreting the measured values from the MAF sensor. But this should only be done after an extensive analysis as the MAF sensor may not be responsible for the symptoms of poor acceleration in your Silverado 1500.Ī more accurate diagnosis can be performed by analyzing the MAF sensor Parameter Identification Data (PID) information on a scan tool. In case of doubt, the sensor may have to be replaced. However, it can happen that there are no error codes.

#Loose transmission filter symptoms code

If you see P0100, P0101, P0102, P0103 or P0104 code in the OBD2 scanner, it indicates a problem with the mass air flow sensor. Reading out the fault codes using a diagnostic device is relatively reliable.

#Loose transmission filter symptoms how to

How to check if the MAF sensor is bad in Chevy Silverado 1500? This can especially happen in older vehicles or in case of rodent damage. In rare cases, it is possible that the fault codes or the symptoms you’re seeing in your Silverado 1500 are not due to a bad MAF sensor, but because of broken electrical wires or a bad connector. In rare cases, the MAF sensor can also be damaged by oil vapors flowing back out of the crankcase ventilation after the engine has been switched off. When driving fast in heavy rain, water can occasionally pass through the air filter and can damage or contaminate the MAF sensor, which can severely impair its functionality.

There is no fixed timeline for when MAF sensors fail, sometimes they can last the lifetime of the vehicle, other times than can fail even before the warranty expires. With a noticeable loss of performance and high mileage, a defective MAF sensor should definitely be considered. As the mileage increases on your Silverado 1500, it can happen that increasingly inaccurate values are sent to the engine control unit. The mass air flow sensor is a wearing part. And over time when enough dust accumulates, the sensor starts to give erroneous readings. When the vehicle is running, dirt and other airborne particles that escape from the air filter can settle on the sensor.

Air filters are effective at cleaning the air to a certain extent. The most common cause of a malfunctioning MAF sensor in Chevy Silverado 1500 is dirt and grime accumulation on the sensor. What causes MAF sensor to fail in Silverado 1500? Dirt accumulation MAF sensor location in Chevrolet Silverado 1500 fourth generation. This can cause the engine warning light to illuminate in the instrument cluster and the fault can be read out by a diagnostic device. The engine runs too “lean” or too “rich”. The optimal amount of fuel can no longer be calculated which results in either too little or too much fuel injected into the combustion chambers. If the MAF sensor is defective or dirty, it does not send correct measured values to the control unit of Silverado 1500. What happens when MAF sensor malfunctions in Chevy Silverado 1500? It is not only important for power delivery in your Silverado 1500, but also for the lowest possible pollutant emissions. The mass air flow sensor is part of the engine’s intake system and is located between the air filter and the throttle body.